ZOELLER PUMP COMPANY

30-0151 Manufacturer may vary by location | Full flow, non-clog design | Neoprene gasket and flapper, weighted with heavy stainless steel metal backing plates and stainless steel rivet | Slips over ABS, PVC, steel pipe or copper piping | Reduces motor and pump noise from plumbing system | Extra wide hinge to reduce hinge stress | Checks backflow of water and sewer gas Sold by EA

30-0015 Manufacturer may vary by location | Full flow, non-clog design | Checks backflow of water and sewer gas | Easy installation, no threading of pipe required | Corrosion resistant, non-metallic parts | Buna N flapper, double shielded with PVC | Suitable for installation below basin cover Sold by EA

137-0001 Effluent, dewatering pump | Handles 5/8" solids | Cast iron body Sold by EA

282-0001 Durable construction, no sheet metal parts to rust or corrode | Corrosion resistant finish | Non-clogging vortex impeller | Oil filled and hermetically sealed | Provides great heat dissipation from the motor, ensuring a long service life Sold by EA

30-0181 Stops back flow of water and sewer gas | Full-flow design | This valve is designed for low pressure sump pump applications and can be mounted either vertically or horizontally | No pipe threading is required | The flexible union slips over ABS, PVC, steel pipe or copper pipe and the couplings on the 1-1/4" to 1-1/2" size can be mounted in either configuration on either end for connecting dissimilar size pipe diameters | The flexible couplings isolate motor noise from the piping and the...

30-0020 Manufacturer may vary by location | Full flow, non-clog design | Checks backflow of water and sewer gas | Easy installation, no threading of pipe required | Suitable for installation below basin cover Sold by EA

314-0002 Cast iron pump housing for long life | Engineered thermoplastic Impeller designed for durability | Permanently lubricated ball bearings | Handle on prime plug allows for easy priming, no tools required | Use for removing water from water heaters, power washing, water transfer and adding propylene glycol anti-freeze to radiant heating lines | One hundred percent factory tested Sold by EA

49-0005 Oil-filled, hermetically-sealed motor with automatic reset thermal overload protection | Rugged, cast iron motor housing with corrosion-resistant, baked-on enamel finish | Efficient heat sink for heat dissipation | Glass-filled polypropylene base and pump housing with no screen | Reliable tethered float switch | Carbon and ceramic rotary seal | Watertight, neoprene seal between motor and cover | Stainless steel screws and hardware | Factory tested after assembly Sold by EA

202-1000 Preassembled pump and tank for easy installation | Economical sewage system designed for freestanding or built-in installation | Requires tank (Z2023000) and bowl (Z2022000) | Perfect for basements, cabins, workshops, garages, additions, pool houses, manufacturing facilities, etc. | No need to destroy concrete floors | No need to elevate floor Sold by EA

503-0005 No electricity required | Works during power failures | No battery to charge | Helps eliminate flooding in basements | Can be used with any existing brand of sump pump | Comes 100% preassembled | Efficient water usage | Non-corrosive materials | High capacity, high head | Municipal/city water pressure powered system Sold by EA

915-0005 Energy efficient grinder pump will handle anything normally found in sanitary sewage | Factory tested | Retrofits into most 18" by 30" and 24" by 24" basins | Completely assembled and includes check valve and high water alarm | Prepiped with 1 1/4" Schedule 40 PVC Sold by EA

140-0005 Oil-filled and hermetically-sealed, automatic reset thermal overload protection | Carbon/Ceramic mechanical shaft seals | Stainless steel bolts and lifting handle Sold by EA

152-0005 Corrosion-resistant, powder coated epoxy finish | Stainless steel lifting handle | Assembled with stainless steel bolts | Non-clogging, engineered thermoplastic, vortex impeller design | Upper sleeve bearing and lower ball bearing running in bath of oil Sold by EA

152-0002 Corrosion-resistant, powder coated epoxy finish | Stainless steel lifting handle | Assembled with stainless steel bolts | Non-clogging, engineered thermoplastic, vortex impeller design | Upper sleeve bearing and lower ball bearing running in bath of oil Sold by EA

153-0002 Corrosion-resistant, powder coated epoxy finish | Stainless steel lifting handle | Assembled with stainless steel bolts | Non-clogging, engineered thermoplastic, vortex impeller design | Upper sleeve bearing and lower ball bearing running in bath of oil Sold by EA

151-0005 Corrosion-resistant, powder coated epoxy finish | Stainless steel lifting handle | Assembled with stainless steel bolts | Non-clogging, engineered thermoplastic, vortex impeller design | Upper sleeve bearing and lower ball bearing running in bath of oil Sold by EA

267-0001 Handles 2" solids | This pump provides reliable service for residential and small commercial applications | The body is powder coated for corrosion resistance | Neoprene square ring and gasket | Oil-filled and hermetically-sealed motor | Oil-lubricated bearings | Corrosion-resistant Sold by EA

294-0004 Handles 2" solids | The Waste-Mate high head sewage pump is ideal for areas with long discharge runs or high heads that a standard sewage pump won�t handle | All Zoeller motors are designed with �Reserve Power� meaning they will not overload at any point on the curve | Heavy cast iron construction | The body is powder coated for corrosion resistance | Heads to 75 Feet Sold by EA

912-0010 Non-clogging vortex impeller design | Durable construction | Operates on a vertical snap-action switch Sold by EA

53-0029 Float-operated, submersible, 2 pole mechanical switch & variable level, long-cycle systems available | Corrosion-resistant, powder coated epoxy finish | No sheet metal parts to rust or corrode | Stainless steel screws, switch arm, guard and handle | No screens to clog Sold by EA

108-0001 Designed for installations in crawlspaces | Helps eliminate water and dampness, mold and fungus, moisture damage, odor and water pooling | System includes automatic pump, 24' hose and tank assembly Sold by EA

72-0001 Thermal overload protection | Non-corrosive, engineered plastic motor housing, pump housing and base | No sheet metal parts to rust or corrode | All stainless steel screws, switch arm and lower motor housing | Oil-free | Two pole, float-operated mechanical switch | Solid, buoyant, polypropylene float | Completely submersible and hermetically sealed | Watertight and dust tight Sold by EA

53-0002 For dewatering or light effluent pumping | Handles 1/2" solids | No sheet metal parts to rust or corrode | Stainless steel screws, switch arm, guard and handle | No screens to clog | Watertight, neoprene square ring between motor and pump housing | Discharge 1-1/2" FNPT Sold by EA

270-0002 Engineered plastic base on model 270 | Not affected by materials normally found in drainage and sewage pumps | Stainless steel screws, bolts and handle | Oil-filled, hermetically-sealed, automatic reset thermal overload protected motor | Neoprene square ring & gasket | Carbon and ceramic shaft seal Sold by EA